NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS ALREADY PASSED

Document Content and Description Below

NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS ALREADY PASSED Dew point is the temperature at which Correct Answer- condensation occurs. You are the NACE Inspector on a tank lining project w... here a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: Correct Answer- Document the problem and advise the Contractor and Owner's representative. If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a Correct Answer- blotter test for the presence of oil and water. Upon arrival of coating materials, the inspector should Correct Answer- observe and document the amount of material and batch numbers. Relative humidity is Correct Answer- a measure of the amount of moisture in the air compared to saturation level. Galvanic corrosion occurs on which of the following substrates? Correct Answer- Metal When applying Thermal Spray Coatings the specification is most likely to reference: Correct Answer- SSPC-CS 23.00/AWS C2.23/NACE No. 12 What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? Correct Answer- 2.5 cm (1 inch) Polymerization is the process of? Correct Answer- Monomers joining together. An exposed area of the substrate or previous coat of a conductive material, often caused by poor application technique is called: Correct Answer- Holiday Checking is: Correct Answer- a fine crack in the surface of a coating that rarely reaches the substrate. Inspection documentation is important because: Correct Answer- Owners use the documentation for a variety of purposes. An Inspectors personal log book should contain: Correct Answer- No comments regarding the application team. You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of action is to: Correct Answer- Review the NACE Attestation prior to making a decision. Good record can provide maintenance departments with detailed information about ALL of the following EXCEPT: Correct Answer- How the item was coated. Non Conformance Reports are completed by the Inspector: Correct Answer- When the Inspector and Contractor deem it to be significant non conforming item. The initial steel condition is important to the NACE Inspector because: Correct Answer- The Inspector may have to reject the steel. The form of corrosion that has the largest potential for unexpected catastrophic failure is: Correct Answer- Galvanic Corrosion What is used to determine compressed air cleanliness? Correct Answer- Profilometer Osmotic blistering is most likely to occur as a result of: Correct Answer- Airless spray application. When performing tests for oil and grease using an ultra violet light, the NACE Inspector should be aware that: Correct Answer- Synthetic oil or grease may not be identified. To achieve consistently accurate results with ALL alt test equipment: Correct Answer- wash your hands before sampling. When holiday testing is required the Inspector is always required to enforce what standard? Correct Answer- NACE SP 0188 If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is: Correct Answer- Level 3 Fine cracks in the surface of a coating that rarely reach the substrate are called: Correct Answer- Checking It is good practice for the NACE Inspector to have instrument calibration certificates available: Correct Answer- At all times. In a non convertible coating the role of the primary solvent is to: Correct Answer- To control the evaporation rate. Removal of weld splatter is required: Correct Answer- When specifically identified in the owners specification. Common errors that may produce inaccurate readings when using a Dial Type Magnetic Pull Off Dry Film Thickness(DFT) gauge include: Correct Answer- Failing to determine the Base Metal Reading(BMR),Rotating the dial too fast when taking measurements, and Measuring ditty, tacky, or soft films. Conventional spray us good choice when: Correct Answer- High quality finishes are required. Which of these tests uses a syringe? Correct Answer- Bresle Patch Which one of these elements is not necessary for corrosion to occur: Correct Answer- Reference Cell Digital hygrometers Correct Answer- determine relative humidity, air temperature,and dew point temperature. Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition: Correct Answer- Rust Grades A-D Inspectors daily reports are used: Correct Answer- By the contractor to estimate the mount of work done that day, To provide continuity between inspectors, To aid in arbitration between the contractor and client, and To help in cases of a coating failure. Silicone coatings are typically: Correct Answer- Applied in very thin films. Excess moisture during holiday testing can cause erroneous by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection. This is often referred to as? Correct Answer- Telegraphing ASTM Standards are applicable: Correct Answer- When specified. The main responsibilities of the Inspector are to: Correct Answer- Observe and report the quality of the work performed. When using a sling psychrometer a very large difference between the wet and dry bulb readings indicates: Correct Answer- Low Relative Humidity The NACE Inspector should perform tests for soluble salts: Correct Answer- When specified. Corrosion generally occurs at which of the following [Show More]

Last updated: 1 year ago

Preview 1 out of 18 pages