Dante Level 1 Cert Test

Document Content and Description Below

Dante Level 1 Cert Test The Sample rate of an audio system dictates - ✔✔the highest audio frequency that the system can handle What is LAN - ✔✔a computer network that interconnects computer... s using a common range of IP Adresses what sample rates are supported by dante - ✔✔33.1kHz up to 192kHz Steps to deleting a subscription - ✔✔1. Open both transmitter and reciever to expose channels 2. click green checkmark at intersection of channels you wish to unsubscribe 3. wait for green checkmark to disappear do dante devices require special IP configurations - ✔✔No, all commonly supported IP address methods are supported how are devices added to a dante network - ✔✔devices are automatically discovered and displayed in the Controller in the dante controller routing tab, a green checkmark indicates - ✔✔subscription successful as sample rate is increased on a device, what other property is usually changed - ✔✔channel count is reduced the easiest way to get ip addresses for a functional stand alone dante netowrk is for all devices to - ✔✔use the "obtain an IP address automatically" setting can dante use fiber instead of copper cables for ethernet? - ✔✔yes are dante audio streams supported over wifi networks - ✔✔no how are devices restored to a dane network after a power cycle - ✔✔devices and connections are automatically restored how does dante interact with energy efficient ethernet (EEE) switches - ✔✔EEE switches are not recommended for use with dante what is meant by a stand alone dante network - ✔✔one that is not connected to the internet or to other networks what does the dante clock master do - ✔✔provides synchronization for all dante devices on the network on a dante network latency is - ✔✔deterministic, set per device what is the correct order of the steps to create a subscription in dante controller - ✔✔1. open the transmitter and receiver to expose channels of each 2. clock at the intersection of the two channels you wish to connect 3. wait for green checkmark to appear the names of the devices and channels in dante are - ✔✔user definable and remembered by devices when should fiber be used for an ethernet connection - ✔✔when runs over 100 m are required does dante require special networking cabling? - ✔✔regular CAT5E ethernet cable is recommended, dante is built to run on standard IP networks, using standard ip equipment and cables dante works best with [blank] switches - ✔✔Gigabit what is latency - ✔✔latency is the audio signal delay in any audio system does a dante network require a special configuration for clocking - ✔✔no, a clock master is always automatically elected by dante aprox how much bandwidth is consumed by 64 channels of audio at 48kHz/ (excluding network overhead) - ✔✔74 mbits/sec what type of switches does dante use? - ✔✔standard if a network is only used for dante and has only one network switch then - ✔✔the network does not require a managed switch where do dante settings reside - ✔✔on the individual dante devices which of the following are diagnostic features of dante controller - ✔✔Latency and clock monitoring a connection between dante audio channels is called - ✔✔a subscription dante devices with different sample rates can be on the same network BUT - ✔✔cannot subscribe channels between them does dante support MIDI - ✔✔no, dante only transports audio data dante transmitters are sources, date receivers are - ✔✔destinations the default latency of 1 ms is - ✔✔very low and suitable for the majority of applications. a gigabit connection can handle how many channels of dante audio at 48k/24bit? - ✔✔512x512 is there any advantage to using automatic IP addressing on a dante nework - ✔✔yes, automatic addressing ensures that devices create a working LAN the bit depth of an audio system dictates - ✔✔the amplitude resolution of each sample how are device names used in dante - ✔✔subscriptions are made from name to name if dante controller is quit while audio is flowing on a dante network, what happens - ✔✔NOTHING. dante controller is not required to be present or a dante network to work what is the best network topology to use for dante - ✔✔star audio sent over a dante network is (relating to compression) - ✔✔uncompressed, bit-perfect dante is an example of - ✔✔an audio over IP solution (AoIP) [Show More]

Last updated: 10 months ago

Preview 1 out of 5 pages